Basic of Electronics,Characteristics of diodes, Simple diode circuits

By Yash Bansal|Updated : August 3rd, 2021

In this article, you will find the Study Notes on Simple Diode and Wave shaping Circuits which will cover the topic as Half wave rectifier, Full wave rectifier, Zener Diode, and Regulator.

1. DIODE AS RECTIFIER

Any electrical device which offers a low resistance to the current in one direction and a high resistance to the current in the opposite direction is called a rectifier. Such a device is capable of converting a sinusoidal input waveform, whose average value to zero, into a unidirectional (though not constant) waveform, with a non zero average component.

In this article, you will find the Study Notes on Simple Diode and Wave shaping Circuits which will cover the topic as Half wave rectifier, Full wave rectifier, Zener Diode, and Regulator.

1. DIODE AS RECTIFIER

Any electrical device which offers a low resistance to the current in one direction and a high resistance to the current in the opposite direction is called a rectifier. Such a device is capable of converting a sinusoidal input waveform, whose average value to zero, into a unidirectional (though not constant) waveform, with a non zero average component.

1.1.  Half wave Rectifier

Half wave rectifier will rectify only half position of input either positive or negative. The basic circuit for half wave rectification is shown in figure 1.

AC voltage across the secondary winding AB changes polarity after every cycle during the positive half cycle of input ac voltage, end a becomes positive w.r.t end B. This makes the diode forward biased and hence it conducts current.

During the negative half cycle end A is negative w.r.t end B. Under this condition, the diode is reverse biased and it conduct no current.

Parameter of output waveform

A. output DC voltage or current

B. output rms voltage or current

C.  Ripple factor

D. Peak inverse voltage

E. Efficiency

C. Ripple factor

A measure of the fluctuating components is given by the ripple factor which is defined as

D. Peak inverse voltage (PIV)

The maximum reverse voltage the diode can with stand without breakdown.

E. Current handling capability of a diode

It is maximum current, that should not exceed otherwise breakdown occurs.

F. Efficiency

It is a measure of the ability of a rectifier to convert AC power into dc power.

(i) Vo (DC) = 0.318 Vm

Output DC voltage is only 31.8% of peak input voltage Vm

(ii) η = 40.5%

Efficiency is only 40.5%, that is only 40.5% is converted into DC remaining will be lost.

1.2.  Full Wave Rectifier

In full wave rectification, current flows through the load in the same direction for both half cycles of input ac voltage. This can be achieved with two diodes working alternatively. For the positive half cycle of input voltage, one diode supplies current to load and for the negative half cycle, the other diode does so; current being always in the same direction through the load.

The following two circuits are used for full wave rectifier

(a) Centre- tap full wave rectifier

(b) Full wave bridge rectifier

1.2.1 Centre-Tapped Full-wave Rectifier

The circuit of a centre-tapped full-wave rectifier is shown in Figure 2(a). This circuit is seen to comprise two half-wave circuits which are so connected that conduction takes places through one diode during one half of the power cycle and through other diode during the second half of the power cycle.

In this rectifier centre-tapped step down transformer has been used, in which secondary winding is divided into two halves, each half having equal number of turns. In N1 : N2 centre-tapped transformer, primary winding has N1 turns and each half of secondary winding has N2 turns.

When centre terminal of secondary winding is grounded, voltage at nodes a and b will have equal magnitude but opposite sign;

i.e., Vb = – Va

if     Va = Vm sinα

then Vb = – Vm sinα

Operation

• When 0 < α < π

Then Va is positive so diode D1 is forward biased and in this case Vb is negative so diode D2 is reverse biased. As diode D1 is in conduction mode so node ‘a’ gets shorted to RL therefore  Vo= Va

• When π < α < 2π

Then Va is negative so diode D1 is reverse biased and Vb is positive so diode D2 is forward biased. As diode D2 is in conduction mode so node ‘b’ gets shorted to RL therefore Vo= Vb

Parameter of full wave rectifier

A. output dc component

B. output RMS value

C. Ripple factor

D. Peak converse voltage

E. Efficiency

1.2.2. Bridge Rectifier

The full wave rectifier circuit requires a centre-tapped transformer where only one half of the total ac voltage of the transformer secondary winding is utilized to convert into dc output. Now consider a different configuration of full wave rectifier circuit, called bridge rectifier, where entire AC voltage of the transformer secondary is used to convert into DC voltage.

Figure 3 shows a bridge rectifier circuit. There are four diodes D1, D2, D3 and D4 which form the four arms of the bridge. AC from transformer secondary is fed to two corners and the load resistance RL is connected to other two corners.

During positive half-cycle of input, point A is positive, diodes D1 and D3 are forward biased and diodes D2, D4 are reverse biased then, the current flows through diodes D1, the load RL and through diode D3 back to the negative polarity of the transformer secondary. During negative half cycle of input point B is more positive than point A, thus diode D2, D4 are forward biased and diode D1 and D3 are reversed biased, then the direction of current flow will be through diode D2 load RL and diode D4. In both case the current flowing through resistor RL is in same direction, thus it is unidirectional current and we obtain full wave rectification.

2. REGULATOR

• The most important property for an ideal power supply is to maintain a constant voltage at the output terminals for all operating conditions.
• But practically there is a drop-in output terminal voltage of the power supply as the load current increases, so we require to regulate the power at optimum level using a voltage regulator.

2.1.  Performance Parameters of a Good Voltage Regulator

• Line Regulation Factor

It is the effect of variations in the supply voltage causing variations in the output voltage of the regulator.

V01 is the output voltage at the maximum input voltage while V02 is the output voltage at the minimum input voltage.

• Output Resistance

For voltage regulation, multiple units of regulator might be cascaded. Thus, to make the coupling smooth the output resistance of the regulator should as low as possible, ideally zero.

• Maximum Dissipated Power

The maximum power dissipation by the Zener diode should be as low as possible.

2.2.  Zener Diode

• Zener diode is a special purpose diode designed to operate under reverse bias in the breakdown region.
• A Zener diode has higher doping than conventional diodes
• In a Zener diode the depletion layer is very thin and electric field strength at the junction is very high even for a small reverse voltage.

2.3.  Application of Zener Diode as a Voltage Regulator

• At the instant when the applied reverse biased voltage on the Zener diode is equal to the Zener breakdown voltage, further increase in reverse voltage makes the electric field at the p-n junction significantly high.
• The electric field is high enough to pull the electrons that are beyond the junction on the n-side towards the p-side, significantly increasing the current.
• The increased current allows a wide range of current to flow through the diode in the breakdown region such that the reverse voltage has no significant change.

2.4   Equivalent Circuit of Zener Diode

2.5.  Drawbacks of Zener Voltage Regulators

• The Zener diode can be operated as a voltage regulator within a limited range of reverse current.
• Power dissipation for the Zener diode is practically large enough to affect the efficiency of the device.
• The output resistance of a Zener voltage regulator is practically not as low as desired for the cascading operation

If you aiming to crack GATE & ESE, Other PSU Exams then you must try Online Classroom Program to get unlimited access to all the live structured courses and unlimited mock tests from the following links:

Click on the Links Below to Avail Test Series:

Thanks

Sahi Prep Hai To Life Set Hai!

Posted by:

Member since Nov 2018
Content Manager (GATE)

write a comment

Venkat RamananDec 9, 2018

Ikw

Venkat RamananDec 9, 2018

Enna

anjaneyulu besthaAug 10, 2019

Study material PDF for ECE subjects sir

JayasriAug 22, 2019

Thank u sir..

MaheshSanthoshDec 15, 2019

Sir..the transition capacitance in diode equivalent model is to be kept in parallel with diode equivalent resistance but in pic you have shown it in series.please correct me if I wrong.

Nishit NathawaniFeb 10, 2020

pls improve error less materials

Akshaya AnandFeb 11, 2020

I can't view any of the videos. Why is that?

Jatin RajoriyaApr 6, 2020

I just want to know for TA HSFC ISRO is same Syallabusas like isro scientists

Amit GuptaNov 21, 2020

Thank you sir

ShivaAug 15, 2021

TV
GradeStack Learning Pvt. Ltd.Windsor IT Park, Tower - A, 2nd Floor, Sector 125, Noida, Uttar Pradesh 201303 help@byjusexamprep.com