**In this article, We are providing the 2nd part of the study notes on Circuits Analysis and Applications of Diodes, BJT, and MOSFET for GATE and other Electrical Engineering exams. The study notes cover the topic such as Analysis of the operating mode of BJT, Operating Point, DC and AC load line, Instability in collector current and BJT Biasing. **

**1.** ANALYSIS** OF OPERATING MODE OF BJT**

**OF OPERATING MODE OF BJT**

** Method-1**

To determine the mode of operation of a BJT, the following steps are followed.

** Step 1 :-** Let Assume that the transistor is biased on the forward active mode,

In this case put

V_{BE} = V_{BE(ON)}, I_{B} > 0 and I_{C} = βI_{B}

** Step 2 :-** Evaluate the linear circuit with these assumption.

** Step 3 :-** Find the each terminal voltagesi.e., V_{B}, V_{C} and V_{E}**.**

** Step 4 :- **Now, the BJT can be considered as two diodes connected back to back as shown below in figure 1

** Step 5 :-** Inspect whether the diodes are forward biased or reverse biased

** Step 6 :- **Conclude the operating mode of transistor for the condition according given in table 1.

** Method-2**

The mode of operation of the Transistor is found by follwing the given steps.

** Step 1 :- **Assume the transistor is biased in the forward active mode. In this case put

V_{BE} = V_{BE(ON)}, I_{B}>0 and I_{C} = βI_{B}

** Step 2 :-** Evaluate the linear circuit with these assumption.

** Step 3 :-** Determine the operating region by following condition

V_{CE} > V_{CE} _{(sat)} Active region

V_{CE} < V_{CE} _{(sat)} saturation region

** Method-3**

To determine the mode of operation of a BJT, the following steps are followed.

** Step 1 :-** Assume the transistor is biased in the forward active region. In this case put

V_{BE} = V_{BE(ON)}, I_{B }> 0 and I_{C} = βI_{B}

** Step 2 :-** Determine the collector current, (I_{C})_{active }for the transistor operating in active region.

** Step 3 :-** Determine the value of collector current (I_{C})_{sat} in saturation mode.

** Step 4 :-** Find the mode of operation by following the given below conditions.

(I_{C})_{sat} < (I_{C})_{active} Saturation

(I_{C})_{sat} > (I_{C})_{active} Active

**2. OPERATING POINT**

- From transistor characteristics, it is clear that a transistor functions most linearly when it is constrained to operate in its active region.
- To establish an operating point in the region it is necessary to provide approximate direct potentials and current, using external source.
- Once an operating point (also known as Quiescent or Q-point) is established, time varying excursions of input signal (base current, for example) should cause an output signal (Collector voltage as collector current) of the same waveform.
- If the output signal is not faithful reproduction of the input signal, for example, it is clipped on one side, then the operating point is unsatisfactory and should be relocated on the collector characteristics.
- Figure 3(a) shows the common emitter circuit (the capacitors have negligible reactance at the lowest frequency of operation of this circuit). Figure 3(b) gives the output characteristics of the transistor used in figure 3(a).
- Note that even if there are freedom to choose R
_{C}, R_{L}, R_{b}and V_{CC}, it is not possible to operate the transistor everywhere in active region because various transistor ratings limit the range of useful operation.

**3. THE DC AND AC LOAD LINES**

The capacitance considered in the circuit of figure 3(a) is large enough so that they act as open circuits under DC conditions but short circuits at the lowest frequency of operation of the circuit. Since the capacitor are open-circuited under DC conditions so the circuit can be redrawn as shown below in figure 3(c)

.....(i)

- Equation (i) represents the dc or static load line of the circuit with a slope of –1/R
_{C}as drawn in figure 3(b). - If R
_{L}= ∞ and if the input signal (base current) is large and symmetrical, operating point Q_{1}must be located at the center of the load line. In this way, the collector voltage and current may vary approximately symmetrical around the quiescent values V_{C}and I_{C}, respectively. - If R
_{L}≠ ∞, however, an ac or dynamic load line must be considered. - Since capacitors act as short circuits at input signal frequency, the effective load at the collector becomes R
_{C}in parallel with R_{L}. - Now, AC or dynamic load line is defined as a line that passes through the dc operating point Q
_{1}and has a slope equal to 1/R'_{L}corresponding to the collector load. =R_{C}||R_{L, }Under AC conditions. This AC load line is indicated in figure 3(b).

**4. INSTABILITY IN COLLECTOR CURRENT**

From the above discussion, it is found that to obtain faithful reproduction of the input signal it should necessary to maintain a stable Q-point.

The collection current can be calculated by the following equation.

I_{c} = β I_{B} + (1+β) I_{co} …………(ii)

From equation (ii), It can be concluded that I_{c} is unstable due to the following reasons:

**(i) Variations in I _{co} **

I_{co} is the reverse saturation current of the collection function. It increases with an increase in temperature because of the increase in the concentration of minority carriers.

- If temperature increase by 1°C then I
_{co}increases by 7%. - For each 10°c rise in temperature I
_{co}

Hence it is observed that variation in temperature causes change in I_{co} and as result, I_{c} also varies.

**(ii) Variation in V _{BE}**

When temp increased 1°C, V_{BE} decreased by 2.5 mV.

Hence, changes in temperature create change in V_{BE} due to which base current (I_{B}) changes. Hence from equ. (ii) it can be concluded that collection current I_{c} also varies.

**(iii) Variation in β**

β varies w.r.t transistor replacement or due to variation in temperature.

- When a transistor is replaced with another transistor, β value will vary because it is practically difficult to find two transistors having exactly same value of β.
- For a given transistor, β also increases with an increase in temperature.

Hence from the above discussion, it can be concluded that I_{c} is unstable due to variation in I_{co}, β and V_{BE} i.e

I_{c} = f (I_{CO}, V_{BE}, β) …………(iii)

From the above equation, It is clear that I_{c} is a function of I_{co}, β and V_{BE.}

By Applying partial differentiation on equation (iii),

ΔI_{c} = s.ΔI_{co} + s’ΔV_{BE} + s”Δβ ………….(iv)

Where s, s’ and s” are **stability factors**.

- From equation (iv), it can be conducted that for greater stability in I
_{c}, ΔI_{c}should be smaller, which is possible when stability factors are smaller. - Instability in I
_{c}has two undesired effects:

(i) The operating point which changes along the load line may result in distorted output and some worst situations the operarting point may move into cut off or saturation region.

(ii) Thermal runaway may occur which leads to damageof a BJT.

- Hence, collector current I
_{c}should be made stable with either stabilization or compensation methods.

**Procedure to find stability factor**

**Step 1:** Find expression for I_{B} by applying KVL in a proper loop in the given circuit.

**5. BJT BIASING **

Biasing is a technique to make the Q-point (Quiescent point or operating point) stable with respect to temperature variation.

Commonly used biasing circuits are:

(i) fixed bias circuit

(ii) collector to base bias circuit

(iii) self-bias circuit

**5.1. Fixed bias circuit**

In figure 4(a), the base current is derived from supply voltage V_{cc} by resister R_{B}. This type of biasing is called fixed bias as V_{cc} and R_{B} are fixed quantities.

The operating point Q_{1} is chosen on load line for a particular Base current I_{B} as shown in figure 4 (c)

By applying KVL in input loop,

Hence from above equ, Q-point (V_{CE}, I_{C}) is calculated for fixed I_{B}.

**Stability factor**

**Disadvantage**

- If β = 100, the stability factor is 101 and the collector current is 101 times that I
_{CO}, reverse saturation current. Hence the stability factor for a fixed biased circuit is very high. So, it will be the least stable biasing arrangement.

**5.2. Collector to base bias circuit **

An improvement in bias stability is obtained if tapping for bias is taken from the collector terminal instead of from the collector supply point as shown in figure 5.

Applying KVL in input loop,

–V_{CC} + (I_{B} + I_{C}) R_{c} + I_{B}R_{B} + V_{BE} = 0

Now applying kVL in the output loop

–V_{cc} + R_{c}(I_{B} + I_{c}) + V_{CE} =0

With the help of above equ, operating point is calculated for given biasing circuit.

**Stability factor**

**Advantage**

- The stability factor is smaller than (β + 1), hence an improvement in stability is obtained over a fixed bias circuit.

**Disadvantage**

- The stability factor depends upon R
_{C}. If R_{c }becomes smaller or zero, then the stability factor becomes very large and I_{C}does not remain stable. - Resistance R
_{B}connected from collector to base causes negative feedback due to which voltage gain of the amplifier's circuit decreases.

**5.3. Self-bias or Voltage-Divider bias**

- If the collector resistance R
_{c}is very small, for example, in a transformer coupled circuit, then there is no improvement in stabilization in collector to base bias circuit over the fixed bias circuit. - A circuit which can be used even if there is zero DC resistance in series with the collector terminal is self-biasing configuration of figure 6(a).
- The current in resistance R
_{E}in emitter lead causes voltage drop which is in the direction of reverse biasing the emitter function. - Since this function must be forward biased, the base voltage is obtained from supply through R
_{1}, R_{2}

**(Note:** If R_{b} = R_{1}||R_{2} → 0, then base to ground voltage V_{BN} is independent of I_{CO}. Under these circumstances For best stability R_{1} and R_{2} must be kept as small as possible.**)**

- The given circuit in figure 6(a) can be simplified by using Thevenin’s theorem. Thevenin’s equivalent can be found between base and ground as shown in figure 6(b).

Now applying kVL in input loop

–V + I_{B} R_{b} + V_{BE} + (I_{B} + I_{C}) R_{E} = 0

By using _{ }

**Stability factor**

**Important point**

- S varies between 1 for small R
_{b}/R_{E}and 1 + β for R_{b}/R_{E}→ infinity - A smaller value of R
_{b}, better for stabilization.

**(Note:** even if R_{b} becomes zero, the value of S can’t be reduced below unity. Hence I_{c} always increases more than I_{co}.**)**

- As R
_{b}to reduced which Q-point to held fixed, the current drawn R_{1}, R_{2}network from supply V_{cc} - Also, if R
_{c}is increased while R_{b}is held constant then V_{cc}must be increased to operate at the same Q-point. - In either case, a loss of power (decreased efficiency) to disadvantage accompanies the improvement in stability.
- To avoid the loss of Ac (signal) gain because of feedback caused by R
_{c}, this resistance is often passed by a large capacitance (> 10 μF), so that its reactance at frequencies under consideration is very small.

Circuits Analysis and Applications of Diodes, BJT, FET, and MOSFET notes explained in the 2nd part are important for the GATE EE, SSC JE EE, ESE IES EE, ISRO EE, and other electrical branch exams.

If you aiming to crack GATE & ESE, Other PSU Exams then you must try Online Classroom Program to get unlimited access to all the live structured courses and unlimited mock tests from the following links:

**ESE and GATE EC Online Classroom Program (24+ LIVE Courses and 150+ Mock Tests)**

**ESE and GATE EE Online Classroom Program (24+ LIVE Courses and 150+ Mock Tests)**

### Click on the Links Below to Avail Test Series:

### Click Here Avail GATE/ESE EC Test Series !!! (150+ Mock Tests)

### Click Here Avail GATE/ESE EC Test Series !!! (150+ Mock Tests)

**Thanks**

**for Preparation**

## Comments

write a comment