ESE 2019: Full Length Mock Quiz-2 for ESE & GATE ME Exams

Question 1

For which of the following sectors do comprehensive safety and health statutes, for regulating Occupational Safety and health (OSH) at work places, exist at present in India?

Question 2

If a solid is cut by a cutting plane parallel to the base of the solid and top part is removed, the remaining part is called

Question 3

Production Scheduling aims to:

Question 4

Match the following

Question 5

Match items from groups I, II and III:
Group-I (Structure)
A) Simple cubic
B) Body centered
C) Face centered
D) Hexagonal closed packed
Group-II (Effective no. of atoms)
P) 2
Q) 1
R) 4
S) 6
Group-III (Co-ordination No.)
T) 8
U) 6
W) 12

Question 6

For an orthorhombic crystal structure the relation between the interfacial angles are given as

Question 7

With reference to the classification used by IUCN’S, consider the following statements:
i. A taxon is considered endangered when more than 70% of its population has been lost in last 10 years.
ii. If reduction in population is more than 90% over the last 10 years, then it is enlisted as critically endangered.
Mark the correct statements?

Question 8

With reference to ‘Agenda 21’, sometimes seen in the news, consider the following:
1. It is a global action plan for sustainable development.
2. It originated in the World Summit on Sustainable Development held in Johannesburg in 2002.
Which of the statements given above is/are correct?

Question 9

A new optical disc format known as the Blu-ray Disc (BD) is becoming popular. In what way is it different from the traditional DVD?
1) DVD supports Standard Definition video while BD supports High Definition video.
2) Compared to a DVD, the BD format has several times more storage capacity.
3) Thickness of BD is 2.4 mm while that of DVD is1.2 mm.
Which of the statements given above is/are correct?

Question 10

Consider the following statements regarding ‘Moon Impact Probe’
1) The Moon Impact Probe (MIP) was a lunar probe released by ISRO’s Chandrayaan-1 orbiter into the lunar south pole
2) With MIP, India became the fifth nation to reach the surface of the moon
3) The MIP had discovered the presence of water on the moon.
Which of the statements given above is/are correct?

Question 11

A single cylinder, four-stroke cycle oil engine is fitted with a rope brake. The diameter of the brake wheel is 600 mm and the rope diameter is 26 mm. The dead load on the brake is 200 N and the spring balance reads 30 N. If the engine runs at 600 rpm, what will be the nearest magnitude of the brake power of the engine?

Question 12

Direction: Each of the question consist of two statements, one labeled as the ‘Statement (I)’ and the other as ‘Statement (II)’. Examine these two statements carefully and select the answer to these items using the codes given below:

Statement (I): In subsonic flow in a diverging channel, it is possible that the flow may separate.
Statement (II): In subsonic flow in a diverging channel, there is adverse pressure gradient in the channel.

Question 13

The involute gears are designed to mesh for a given centre distance and a given angular velocity ratio (other than 1). During assembly, the centre distance has increased slightly. Then which of the following changes occurs?
1) Velocity ratio changes
2) Pressure angle changes
3) Pitch circle diameter changes
4) Working depth changes
5) Base circle radius changes
Select the correct answer using the code given below.

Question 14

Two links are shown in Coriolis component figure where first link speed with respect to second link speed is 15 m/sec. If second link rotates at fixed speed of 80 rpm, then find magnitude of Coriolis component of acceleration of first link?

Question 15

Autofrettage is a method of

Question 16

A: A shaft with large polar moment of inertia twists less under a given force.
R: Polar moment of inertia is independent of the area moment of inertia.

Question 17

Arrange the following according to their increasing calorific values?

Question 18

PLC's I/O capability will include signal from:

Question 19

Directions: Each of the next items consists of two statements, one labeled as the ‘Statements (I)’ and the other as ‘Statement (II)’. You are to examine these two statements carefully and select the answers to these items using the codes given below:

Statement (I):In drawing process, cross-section of round wire is reduced by pulling it through a die.
Statement (II): Bundle drawing produces wires that are polygonal in cross-section rather than round.

Question 20

For increasing the material removal rate in turning, without any constraints, what is the right sequence to adjust the cutting parameters?
1. Speed
2. Feed
3. Depth of cut
Select the correct answer using the code given below:

Question 21

Directions: The following items consists of two statements, one labelled as ‘statement (I)’ and the other as ‘statement (II)’. You are to examine these two statements carefully and select the answer to these items using the codes given below:

Assertion (A):A cotter joint is used to rigidly connect two coaxial rods carrying tensile load.
Reason (R):Taper in the cotter is provided to facilitate its removal when it fails due to shear.

Question 22

Directions: The following items consists of two statements, one labelled as the Assertion ‘A’ and the other labeled as Reason ‘R’. You are to examine these two statements carefully and select your answers to these items using the codes given below:

Assertion (A): Value Engineering is concerned with increasing the quality of the product even at enhanced cost to fulfil the customer requirements.
Reason (R): Customer requirements are changing very rapidly and survival of a manufacturing industry is linked with fulfilling the customers requirements.

Question 23

A wall of 0.6m thickness has normal area of 1.5 m² and is made up of material of thermal conductivity 0.4 W/mK. If the temperature on the two sides of the wall are 800 °C and 1000 °C, the thermal resistance of the wall is

Question 24

Direction: Each of the question consist of two statements, one labeled as the ‘Statement (I)’ and the other as ‘Statement (II)’. Examine these two statements carefully and select the answer to these items using the codes given below:

Statement (I): Providing reheat in a Rankine cycle would increase the efficiency of the cycle.
Statement (II): Reheat in Rankine cycle reduces specific steam consumption.

Question 25

Impact resistance of a material will not depends on: